T6
LED Tunnel Light
T6
Patent dustproof downwind cooling design specially for tunnel, durable and high efficient heat dissipation.
Patent shockproof design, the structure instead of the screws supports the weight, very safe and reliable.
Imported optical PC lens, strong antiaging performance and good light transmission.
Combined with an integrated lens and lower current to drive the latest high brightness outdoor SMD LED chip, the overall light efficiency is improved by 10%.
Flexible angle adjustment, interval ≤10 °.
Adopt the overall structure waterproof design, ≥IP66.
1. As Figure 1: Remove the M5 bolts (including nuts, flat washers and spring washers) from the angle adjuster. Install the L-shaped fixing part from the internal of the lamp, install the flat washers, tighten the M8 screws and the angle adjustment screw;
2. As Figure 2: According to the hole size in the size table, drill 4 installation holes at suitable positions on the tunnel wall;
3. Use 4PCS M10 expansion bolts to install the lamp on the tunnel wall.
4. Confirm the installation direction of the lamp (the lens arrow always points diagonally upwards or points to the opposite wall), fix the lamp on the four expansion bolts in the direction, remove the positioning screw, and fix the positioning screw at the hole position at the right angle, tighten the angle adjustment screw;
5. As Figure 3: Connect the power cord of the lamp to the AC power cord correctly.
6. According to the actual lighting requirements on site, you may loosen the angle adjustment screw on the angle adjuster, adjust the lamp to the appropriate angle (around 15° from the horizontal level of the tunnel, depending on the arc of the tunnel), then lock the bolt tightly.
Inspection:
1. Firmness, neatness; direction, angle.
2. The wire is not exposed and the wire sheath is not damaged.
3. Power-on check (air switch and other devices need to be turned to the ON position). For the lamps with control system and so on, it is necessary to coordinate the whole. For the lamps with wrong installation, it is necessary to disconnect the power and start the installation again.
Open box to check
1.Before unpacking, check whether the packing box is damaged, check whether the attached technical documents, such as manuals and certificates of conformity, are complete, and check whether the lamp parts are damaged or loose.
Precautions:1. Read the instruction manual carefully before using the product to avoid damage or accidents.
2. The lamps should be handled with care, and the non-installed parts of the lamps should be prevented from collision and scratches.
3. The wiring of the lamp should be correct, and the connection of the wire passing through the lamp should not bear additional external force and wear.
4. Before installing the lamps, the power supply must be cut off, and live work is strictly prohibited.
5. The lamp is not suitable for direct installation on the surface of common combustible materials.
6. If the lamps are not transported as a whole, the accessories need to be assembled on the lamps.
7. If the lamp is equipped with an air switch and other devices, it needs to be turned to the OFF position.
8. Use insulating gloves to ensure body insulation and avoid accidents.
9. The lamps and lanterns of the three-phase power supply system should be wired according to U, V, and W in order to ensure the three-phase balance of the power grid.
10. The lamps should be carefully checked before installation and use. If any abnormal phenomenon is found, please contact our company.
11. Before installation, ensure that the lamps are in good condition before they can be installed and used.
12. It should be fastened and reliable during installation.
13. Installation requires the guidance of relevant qualified personnel. Can be used indoor and outdoor. The foundation can support the light fixture.
14. The light source in this lamp can only be replaced by DIANMING employees, designated agents or persons with similar qualifications.
15. This product is maintenance-free and generally does not require maintenance. If you need maintenance, please contact our company.
Transportation and storage requirements1. The lamps shall not be subjected to severe mechanical impact, exposure to sunlight and rain during transportation, and shall not be upside down.
2. Lamps should be stored in a warehouse with an ambient temperature of -30℃~+60℃, dry, clean and well-ventilated, without corrosive medium, and should be kept away from fire and heat sources